CALL 210-556-1743

Menu





























Cup Bur Tool

 

How to use the Cup Bur jewelry making tool to round the end of jewelry wire when making ear wires:

For most jewelry wire components, it is very important to cut the wire properly, so that the sharp end of the cut wire ends up in the trash and the flat end of the cut wire remains on your jewelry wire component.  With most jewelry items, just cutting the jewelry wire properly will be enough.  Most of the jewelry designs that we make do not require us to file the cut end of the jewelry wire, either because the cut end is hidden within a loop, or because the cut end is wrapped around itself.  The exception to this is that when you are making your own ear wires out of jewelry wire it is very important that you remove the burs from the cut end of the ear wire.  In the picture below-left, you can see the cut end of the wire, that was cut properly and is flat, but has sharp edges.  In the picture below-right, you can see how the end of the wire was filed until it is rounded.  This is what you need for your ear wires.

Jewelry wire cut with flush cutter jewelry making tool. Jewelry wire cut end round by Cup Bur jewelry making tool.
Before using cup bur tool After using cup bur tool

Now that we have established why it is important to remove the burs and round the cut end of the jewelry wire when making earrings, let's discuss how we do this.  The tool we use to round the cut end of the jewelry wire is called a cup bur, or alternatively a bur cup.  We sell two different styles of cup bur tools, our item 0303, economy cup bur and our item 0387, cup bur premium.  Item 0303 comes on its own wooden handle.  Item 0387 requires that you use a pin vise tool, item 0388 as the handle.  The pin vise must be purchased separately.  You can view these two jewelry tools below.

Item 0303 Item 0387

Using the cup bur tool is rather simple, as shown below you fit the cup end of the cup bur tool on the end of your jewelry wire and then you rotate the tool with your fingers.  You don't need to rotate in only one direction.  It is much more efficient if you rotate clockwise as far as your grip will easily allow then rotate counter-clockwise back to the starting position.  Repeat this process for about 20 to 30 seconds and you should notice that the end of your jewelry wire is rounded.  When we use the tool, we like to rotate the cup bur both on the axis of the wire and at a 30 degree angle to the axis of the wire.  We also like to rotate the 30 degrees to be up, down, left and right to help round the edges of your jewelry wire.

Jewelry wire showing rounding the end of the jewelry wire using the CupBur jewelry making tool.
Jewelry wire showing rounding the end of the wire using the Cup Bur Jewelry Tools off the axis of the wire.
On Axis 30 Degrees Off Axis

Please select here to view our video on how to use the cup bur jewelry tool

Please note that the cup bur bits only come in one size.  The size is appropriate for 18, 20 or 21 gauge wire.  It will not work for 16 gauge or larger gauges of wire.  It will not work well for 22 and smaller gauges of wire.  Normally, the cup bur tool is used when making ear wires, to round the end of the ear wire. 

Summary on using the Cup Bur jewelry making tool to round the end of cut jewelry wire:

In summary, for most jewelry wire components, we don't take any steps to round the cut end of the wire, but we are careful that we cut the wire with the flat end of our flush cutter toward the finished jewelry wire component.  This leaves a flat end on the jewelry wire.  For ear wires, that flat end of the cut jewelry wire is always too sharp and we use a cup bur tool to file the ends of the cut wire until it is rounded.


Please select here to return to our beginner's jewelry making skills web page.

 

 



© 2012 WigJig @ wigjig.com
 

Privacy Policy • All WigJigs and Accessories are patented or patent-pending • All rights reserved ©2017